Dual Motor TinyShield

ASD2302-R

32 in stock


  • Free Shipping for orders over $50
  • Available Worldwide


  • DESCRIPTION

    The Dual Motor TinyShield allows you to drive two independently controlled DC brushed motors from your TinyDuino. Create your own tiny robots or drones! Using two of the super miniature but very powerful 2mm x 2mm TI DRV8837 Motor Driver (H-Bridge) IC, this shield will allow for up to 1.8A per channel and operate motors between 1.8 to 11V. This TinyShield includes a built in motor controller to make driving motors simple and uses the TinyDuino I2C interface - saving GPIO pins on the TinyDuino processor for other tasks. An easy-to-use Arduino library is provided to control this..

    To learn more about the TinyDuino Platform, click here

      TECH SPECS

      To see what other TinyShields this will work with or conflict with, check out the TinyShield Compatibility Matrix

        TI DRV8837 H-bridge motor driver

        • Low MOSFET On-Resistance: HS + LS 280mOhm
        • 1.8A Max Drive Current (Recommend 500mA max)
        • 1.8V to 11V Motor Operating Supply Voltage Range

          TinyDuino Power Requirements

          • Voltage: 3.0V - 5.5V 
          • Current: 5mA (Logic only)

          Pins Used

          • A5/SCL - I2C Serial Clock line
          • A4/SDA - I2C Serial Data line

          Dimensions

          • 20mm x 20mm (.787 inches x .787 inches)
          • Max Height (from lower bottom TinyShield Connector to upper top TinyShield Connector): 5.11mm (0.201 inches)
          • Weight: 1.62 grams (.06 ounces)

          NOTES

          • While the DRV8837 supports 1.8A @ 11V, we highly recommend operating under 500mA @ 5V per channel unless you have some really good heat sinking in place.
          • Up to 4 Dual Motor TinyShields can be stacked together in one TinyDuino stack. However, the I2C address needs to be different for each TinyShield. This can be changed with resistors R1 and R2 (soldering is required for this).   
          • By default, the motor power supply input connection is connected to the VBATT connection on the TinyDuino. Therefore, you can run your TinyDuino and the motors off the same battery when it's plugged into this TinyShield.  However, when using this, be sure not to exceed 5.5V on this power input or it will damage the TinyDuino circuitry.  If a higher motor voltage is required, you can remove resistor R3 which will allow you to run the motor voltage independently from the TinyDuino logic voltage.   
          • Even though the motor driver can support 11V at 1.8Amps, we do not recommend using more than a 5V motor at 500mA due to the small size.  
          • Be sure that your power supply is sufficient to operate these motors as well as your logic – batteries are the best. If you are running both the motors and the logic off of one power supply, we recommend avoid using a switching power supply as the transients caused can potentially damage items connected to the logic side.
            •  

            DOWNLOADS

            LEARN

            Dual Motor TinyShield Tutorial
            This tutorial will teach you how to use the Dual Motor TinyShield so that your next project can use some tiny motors.
            Tiny Bluetooth Fan Boat
            Tiny Bluetooth Fan Boat
            Learn how to build a tiny fan boat that you can control via Bluetooth LE right off your mobile device!

            TinyHoverCraft Tutorial
            TinyHoverCraft Tutorial
            Learn how to build a hovercraft that you can control with any TV remote!
            TinyDuino Robot Controller
            TinyDuino Robot Controller
            Learn how to build a simple RC robot in this simple tutorial!



            Related Items

            Servo TinyShield ASD2303-R
            Servo TinyShield
            The Servo TinyShield allows you to drive four independently controlled Servos from your TinyDuino! An external power connection is supplied to conn...