All Products


TinyLily LED 1206

$ 0.84

$ 0.99
A standard size LED in an extremely compact size of 10.2mm x 4mm, with two standard TinyLily sewtabs and a current limiting resistor, so you don’t have to worry about blowing it up or adding an external resistor.

Learn More →



TinyLily LED 0402

$ 0.84

$ 0.99
So you want the smallest possible sewable LED for your project? Try out the TinyLily LED 0402 which sports a total size of just 6.5mm x 2.5mm!

Learn More →



Connect up your TinyLily Mini to standard battery packs that use the JST SH connector (the kind that we sell at TinyCircuits). You can also use this without the JST connector with two large through holes to connect to an external power supply or battery pack.

Learn More →



When TI came out with the world’s smallest DC motor driver chip, we knew we had to build a board around it. Based around the 2mm x 2mm TI DRV8837 Motor Driver (H-Bridge) IC, this board is incredibly tiny at only 10mm in diameter, yet can drive a 5V 500mA motor!

Learn More →



TinyLily Switch 3mm

$ 2.51

$ 2.95
A nice tiny washable switch (the switch itself is just 3x3mm) in an extremely compact size and incredibly thin. This is a momentary push switch, the two contacts are connected when the switch is pushed and open when it’s released.

Learn More →



This is the 3D printed enclosure (both the top and bottom haff), and a watch wrist strap to use to create a TinyScreen Smart Watch.

Learn More →



This TinyDuino Starter Kit is a great way to start with your TinyDuino and begin creating some cool projects! This kit comes with a TinyDuino processor with lithium battery support, a USB TinyShield, a 16 Green LED TinyShield, three Proto Board TinyShields and a 140mAh Lithium Polymer battery.

Learn More →



EEPROM TinyShield

$ 8.46

$ 9.95
Add robust storage memory to your TinyDuino with this EEPROM TinyShield. Build around the Microchip 24FC1025, this is Electrically Erasable PROM (EEPROM) is a simple way to add robust memory storage to your projects and is very low power.

Learn More →



Add huge amounts of storage to your TinyDuino projects by using the 8GB microSD card, with Adapter to standard SD Card size.

Learn More →



Add robust, lightning-fast storage memory to your TinyDuino with this Flash Memory TinyShield. Built around the Winbond W25Q80DV, this board is a simple way to store settings, logs, or any other data your project needs to keep through power cycles.

Learn More →



Connect your projects to the internet with the WiFi TinyShield! Based on the Atmel ATWINC1500 WiFi module, this module supports 802.11 b/g/n, SSL, different security modes (WEP, WPA, WPA2, and unsecured connections) and has a built in TCP/IP Stack that offloads network processing from your TinyDuino.

Learn More →



Connect to your smartphone or computer using Bluetooth Low Energy. This module supports both master and slave modes.

Learn More →



SRAM TinyShield

$ 8.46

$ 9.95
This SRAM Tinyshield allows you to add memory to your TinyDuino projects that can read and write at a virtually instant rate. Built around the Microchip 23LC1024, this board allows for some extra processing memory when your Arduino device is powered on.

Learn More →



TinyZero Processor Board

from

$ 16.96

$ 24.95
The TinyZero is TinyCircuits' second generation processor board, running faster and with much more memory than the standard TinyDuino.

Learn More →



Gift Card

from

$ 8.50

$ 100.00

Learn More →



This is a tiny rechargeable Lithium ion polymer battery that fits perfectly behind the TinyDuino Processor board to power your projects. The battery has a capacity of 70mAh at 3.7V.

Learn More →



This is a rechargeable Lithium ion polymer battery that works perfectly with the TinyDuino Processor board to power your projects. The battery has a capacity of 1100mAh at 3.7V.

Learn More →



Servo TinyShield

$ 12.71

$ 14.95
The Servo TinyShield allows you to drive four independently controlled Servos from your TinyDuino! An external power connection is supplied to connect up to your power source (like a battery).

Learn More →



This TinyShield features four of our popular TinyShield Sensors on a single board!

Learn More →



This is the same connector that can be found on our batteries and speakers. This connector is pre-wired with your choice of 50mm or 100mm wire length.

Learn More →



This is the same connector that is used on servos and other RC equipment. You can use it supply power or PWM signals to or from your TinyDuino Project and interface with standard radio control components.

Learn More →



Start designing your own interactive and programmable projects with the Crazy Circuits Deluxe Set. Use the included Touch Board to turn any conductive material into an interactive surface. Add parts and programing to your next LEGO ™ project to give it dazzling effects.

Learn More →



Create your own electronics projects in minutes with the Crazy Circuits Starter Set. Design your own projects from scratch or follow one of our many Project Guides. Add Crazy Circuits parts to any LEGO™ project to make it light up. Use the included conductive thread to create eye catching wearables.

Learn More →



Connect to your smartphone or computer using Bluetooth Low Energy. The Nordic chipset used on this TinyShield only supports slave mode.

Learn More →



These connectors are commonly used on micro servos and other RC equipment. You can use it supply power or PWM signals to or from your TinyDuino Project and interface with standard lightweight radio control components

Learn More →



Add motion to your TinyDuino project! This gear motor uses the same JST connector that can be found on our Dual Motor TinyShield, meaning it can be plugged right in without any soldering or crimping.

Learn More →



45mm Wheel

$ 3.36

$ 3.95
Add motion to your TinyDuino project! This wheel has a grippy rubber tire for good traction and has a strong plastic center hub, which makes it perfect for robotics projects.

Learn More →



34mm Wheel

$ 3.36

$ 3.95
Add motion to your TinyDuino project! This wheel has a grippy rubber tire for good traction and has a strong plastic center hub, which makes it perfect for robotics projects.

Learn More →



Add sound to your TinyDuino project! This speaker uses the same JST connector that can be found on our microSD and Audio TinyShield, meaning it can be plugged right in without any soldering or crimping

Learn More →



This radio TinyShield is based around the very popular Nordic NRF24L01+ radio transceiver. The TinyShield is set to operate at 2.4GHz, can transmit at up to 2Mbps, and is very easy to use. This transceiver allows for long range communication between radios and is designed for an open field range of up to 500 meters

Learn More →



Is your TinyDuino looking a little bare? Stick it in a plastic enclosure box to protect it and give your project a clean look! This enclosure box is made of sturdy black plastic, which makes it easy to cut and drill. It also makes this little box tough! The two halves are assembled with two steel screws to hold it together.

Learn More →



Is your TinyDuino looking a little bare? Stick it in a plastic enclosure box to protect it and give your project a clean look! This enclosure box is made of sturdy black plastic, which makes it easy to cut and drill. It also makes this little box tough! The two halves are assembled with two steel screws to hold it together.

Learn More →



What project would be complete without magnets? These magnets can help you do anything from hold something shut, to detecting the position of something with a hall effect sensor. They're neodymium magnets, so don't let their small size fool you. They pack a big punch!

Learn More →



Need a way to mount our gear motors to your project? Look no further. This plastic mount holds the motor tight and mounts securely with two included screws and nuts.

Learn More →



Pre-Wired 3mm LED

$ 0.84

$ 0.99
This is one of the easiest ways to add some color to your TinyDuino project. These crystal clear 3mm LEDs are already wired with a built in current limiting resistor, so all you need to do is solder the pre-tinned wires to a power source.

Learn More →



Add motion to your TinyDuino project! This gear motor uses the same JST connector that can be found on our Dual Motor TinyShield, meaning it can be plugged right in without any soldering or crimping.

Learn More →



This is the best 2.5g servo we've found so far. If you need high torque and precision in a truly tiny package, this is the one to get. It is a digital servo so position accuracy is second to none.

Learn More →



This is a rechargeable Lithium ion polymer battery that works perfectly with the TinyDuino Processor board to power your projects. The battery has a capacity of 850mAh at 3.7V.

Learn More →



This is a rechargeable Lithium ion polymer battery that works perfectly with the TinyDuino Processor board to power your projects. The battery has a capacity of 500mAh at 3.7V.

Learn More →



5x5 Tiny Breadboard

$ 2.51

$ 2.95
Sometimes you need a good old fashioned breadboard to easily test a circuit. Now you can make truly minuscule prototypes using these miniature breadboards.

Learn More →



Mini Breadboard

$ 3.36

$ 3.95
Sometimes you need a good old fashioned breadboard to easily test a circuit. Now you can make compact prototypes using these mini breadboards.

Learn More →



12mm Hex Adapter

$ 2.51

$ 2.95
This adapter allows you to drive standard 12mm hex RC wheels or anything else that uses a 12mm hex drive.

Learn More →





If you need high torque and precision in a tiny package, this is the servo to get. It is a digital servo so position accuracy is second to none.

Learn More →



If you need high torque and precision in a small package, this is the servo to get. It is a digital servo so position accuracy is second to none, and it has metal gears.

Learn More →



This rechargeable Lithium Ion Polymer Battery is a cylindrical 18650 cell that is typically used in everything from small flashlights to electric cars. The battery has a capacity of 2500mAh at 3.7V, the voltage can range from 4.2V when fully charged to 3.0V when completely discharged.

Learn More →



TinyLily RGB LED

$ 1.66

$ 1.95
This sewable board features a 5mm RGB LED, enabling you to add 24-bit resolution color to your Tiny Project! This LED has a built in driver IC, so it requires special libraries and serial data, not just applied voltage.

Learn More →



This sewable board features a 5mm RGB LED, enabling you to add 24-bit resolution color to your Tiny Project! This LED has a built in driver IC, so it requires special libraries and serial data, not just applied voltage.

Learn More →