The most noticeable feature of the new Tiny Arcade is that the screen and processor board are now attached via a flat-flex ribbon connector rather than 0.1" headers. We've also chosen a newer, smaller speaker, removed the back acrylic pieces.
Upon opening your new Tiny Arcade, you'll want to make sure that you have the following:
The first step will be to assemble the electronic components and give them a quick test. We'll start with the processor board and the screen. Be sure the power switch is in the OFF position, and the sound switch is in the ON position.
Locate the flat-flex ribbon cable and gently insert it into the connector on the Processor board. Make sure the metal contacts are facing the proper direction. Also, be very careful not to bend the connector harshly; it is fragile.
Next, insert the other end of the ribbon cable into the connector on the screen.
With these in place, we can now connect the battery to the on the processor labeled "BATT". The speaker connector is the same size and shape, so make sure to not mix them up. Plug the speaker into the connector on the processor board labeled "SPKR".
Give the electronics a quick test by switching on the power. You should see the screen light up with the TinyCircuits logo, then move to pre-loaded games menu. Use the joystick to scroll between the games. Tiny Shooter is a great game for quickly testing all of the controls. Use the left push button to select the game, and the right push button to insert a coin and start the game. Push the joystick in each direction and watch the space craft to ensure that the up, down, left, and right controls all function. Push the right push button to fire the lasers, and listen for the sound effects. If you don't hear anything, check that the audio switch is in the ON position and that the speaker connector is fully inserted. If the speaker seems quiet, don't worry; it will be louder once it's attached to the acrylic.
NOTE: We test each and every Tiny Arcade thoroughly before shipping to ensure all parts are functional. This test is to make sure you have everything connected properly.
With the electronics functioning properly, we can prepare the acrylic. The first sheet should have both side pieces, and the second sheet should contain seven different pieces that will make up the front, top, and bottom of the cabinet. If it seems like you're missing pieces, check the box, as they may have come detached from the sheet. The next step will be to break the pieces away from each other and remove the thin connecting stubs. Once all of the pieces have been separated, we will peel back the protective paper from both sides. After this step, you may choose to add the included stickers to your acrylic pieces. (This is the most convenient time to add the stickers.)
Now that you have the electronics ready, and the acrylic prepared, we will begin assembling. Make sure wipe off the inner side of the acrylic pieces as you proceed to avoid fingerprint marks that will be hard to clean once the cabinet is fully assembled.
Start by attaching the screw and standoff post to the right wall of the Tiny Arcade. Lay this flat on your table or work-surface.
Place the next piece over the joystick and push buttons on the processor board. Remove the protective covering from the screen.
Insert the electronics into the side wall, aligning the tabs with their corresponding holes. You may have to hold these in place with a few fingers as you insert the next two acrylic pieces.
Place the piece that covers the screen, and then place the front piece that covers the bottom half of the Tiny Arcade.
We will now attach the left side wall. You'll need to route the battery and speaker wires through the gaps on the circuit board to avoid pinching them between the board and the acrylic. Thread the second screw into the post and tighten it a few turns to hold the left wall loosely in place as you align it with the other tabs.
The trick is to get all of the tabs aligned at the same time. You can start at the top and work your way down, aligning the screen with the vertical tab holes, then the processor board with its corresponding tab holes, etc. until all the pieces are in place.
Once these pieces are all in place, fully tighten the screw to hold everything together. Be careful not to over-tighten, as this will separate the acrylic at the top of the cabinet.
We'll now place the remaining acrylic pieces. The first one goes on the front of the arcade in front of the joystick and pushbuttons. (If you're having difficulty inserting this piece, you can loosen the left screw about one rotation, being careful not to let the already attached pieces come apart. This can be re-tightened after all pieces have been properly inserted.)
Next, insert the piece for the bottom of the cabinet.
Insert the cover for the top of the cabinet, then the piece directly in front of that.
To attach the speaker to the cabinet, peel off the protective paper and press it firmly to the inside of the side wall. This type of speaker uses the surface of the attached material to amplify sound waves, so make sure it is well-adhered!
With your Tiny Arcade assembled, you can enjoy the preloaded games, download our latest game releases for free from our website, or use our online tutorial to learn how to develop your very own game for the Tiny Arcade! As always, if you have any questions or feedback, feel free to email us at email@example.com.